![\"crappy_cardboard_box_set\"](\"https:\/\/www.mbeckler.org\/blog\/wp-content\/uploads\/2016\/01\/crappy_cardboard_box_set-262x300.png\")
\nFor Christmas 2015 I wanted to get the Harry Potter Hardcover Box Set for my dearest wife. The official box set hardcovers are very expensive ($120+) and come in a pretty cheap-looking cardboard “trunk” (photo at right). Plus, we already had all the books in hardcover, so I thought I would make a cute little wooden trunk myself. Everyone loves homemade gifts.<\/p>\n
Lots of time and money later, I had finished a nice trunk, perfectly-sized for all seven HP hardcovers. Like all projects, I should have taken more photos during the process, but hopefully this write-up gives you a decent idea of what I did and how you could do the same if you want.<\/p>\n
![\"books_in_trunk\"](\"https:\/\/www.mbeckler.org\/blog\/wp-content\/uploads\/2016\/01\/books_in_trunk.jpg\")
<\/p>\n
<\/p>\n
My plan was to use nice hardwood to build a simple box. I wanted to make it look somewhat like a trunk, but without getting too complex in terms of build. Most trunks I have seen have had some wooden banding, metal hardware accents, and a lock. I discovered a website called Antique Hardware & More<\/a> that sells a variety of trunk hardware pieces, including many for “doll trunks” (which are scaled-down trunks for dolls and doll clothes) that would be perfect for my little trunk. I decided to go with these pieces of hardware:<\/p>\n Based on the size of those items, I went to browse the selection of hardwood at the local home improvement store. My nearby Home Depot stocked oak hardwood with thickness of 0.75 inches, and oak corner molding that was 1″ wide on the outside, and 13\/16″ on the inside. I I sketched out a few designs in my notebook for a trunk make from six flat pieces, with the corner molding on the outside edges. But first, I needed to measure the size of the books, which came out to be approximately 12.5″ wide, 9.25″ tall, and 6.5″ in the third dimension. Page 2 includes the detailed design top view and front view, including extra space for felt. Page 3 is the cutting plan with laser-cutter region notes, plus notes about laser engraving settings.<\/p>\n Here’s a cleaned-up version of the cutting plan. I like using Inkscape with real-world dimensions when planning things that represent the real-world, so that way I can be 100% certain that my plan will work.<\/p>\n With the design fleshed-out, I was ready to start cutting and drilling and building. Unfortunately by now it was December in Minnesota, and I had to either make a mess in our nice heated office at W&L, or work in the freezing cold garage. I did a little of both, and it didn’t make a huge mess either.<\/p>\n The first step was to build a six-sided box with a hinged lid. Using a table saw I measured twice and cut once, to create the six pieces from the cutting plan above. I drilled and countersunk holes for the screws, and assembled the five pieces for the bottom part of the box.<\/p>\n Despite my best efforts, the box was a little bit out of alignment when assembled. Maybe the wood shrunk and twisted as it dried (or soaked up moisture from the garage), or maybe my fabrication skills aren’t as good as I had hoped, but it was a little bit annoying that the edges did not perfectly align. I had to use a chisel and plane to remove the excess wood in places to try to avoid gaps.<\/p>\n I thought this would be a good time to do a test-fit with one of the books.<\/p>\n The book fit well, and there was still some wiggle room for adding the nice green felt lining.<\/p>\n This part took a long time and was quite frustrating. I bought oak corner molding, and used a miter box to cut it to size, so I could put it on all twelve edges of the six-sided box. It was difficult to get the diagonally-cut pieces of molding to butt together nicely, and it took a lot of trial and error with a plane to make things look halfway decent. In the end it didn’t matter, since the screws of the corner metal pieces ended up making gaps between most pieces anyway. Probably not the best plan but it still looks pretty nice.<\/p>\n After cutting each piece of molding I clamped it to the box, then used the drill press to drill a hole through the molding and into the box for the nails. I probably should have used glue too, that may have helped with minimizing the gaps from the corner pieces’ screws.<\/p>\n After the molding was attached I moved on to the metal hardware. The eight corner pieces needed to have their holes marked and drilled, then screwed in place. Initially I forgot how strong real hardwood is (and forgot how weak brass screws are), and broke off a couple screws in holes drilled too small, so I used the next larger drill bit and didn’t have any trouble.<\/p>\n The leather carrying handles are each attached using two metal brackets, which were simple to attach. I sort of estimated where to put the handle brackets based on how much slack was needed to get your fingers between the handle and the box. The hinges were tricky (I’ve never been good at hinges) since the molding around the lid meant the hinges couldn’t be attached to the box itself, but needed to be offset further back to properly align. I cut two pieces of extra oak to compensate for the gap. The lid is a little crooked and one corner is a little higher than the other, but it still looks nice. The felt helps hide the imperfections.<\/p>\n I used plain white glue, spread very thin, to attach the felt to the inside of the box and underside of the lid. Be careful not to press-down on the felt with too much force, otherwise the glue will seep through and make the top of the felt rough and crunchy.<\/p>\n Since Christmas was coming up rapidly, this is how far I was when I gave it to my darling wife Anna. I resolved to finish the rest of it (staining and artwork) within a month after Christmas.<\/p>\n I wanted to add a bunch of Harry Potter artwork to the outside of the box to make it look nice. Since I have access to a laser cutter\/engraver, I planned to use that to add artwork directly on the box. However, after doing some test engraving on some oak scraps, I realized that the grain of the wood makes it kind of difficult to see the detail in the engraving.<\/p>\n Instead of engraving directly on the box itself, I decided to instead laser engrave and cut-out the designs from the usual 3mm Baltic birch plywood that we use for all<\/a> sorts<\/a> of other<\/a> projects<\/a>. This worked much better, and added some needed depth to the designs. Also, the smooth grain of the birch showed the engraving detail better, and the interior layer of darker wood accepted the stain more, leading to better contrast between engraved and non-engraved parts.<\/p>\n I first cut the Harry Potter wordmark (the lightning bolt “Harry Potter” from the title screen of the films) from 3mm maple. Here’s a short video of part of that laser cutting:<\/p>\n\n
![\"notebook_pages_600\"](\"https:\/\/www.mbeckler.org\/blog\/wp-content\/uploads\/2016\/02\/notebook_pages_600.png\")
(Click to open PDF of notebook scans – 3 MB)<\/a><\/p>\n![\"cutting_plan\"](\"https:\/\/www.mbeckler.org\/blog\/wp-content\/uploads\/2016\/01\/cutting_plan.png\")
<\/p>\nProduction Step 1 – Build a box<\/h1>\n
![\"box_assembled_top\"](\"https:\/\/www.mbeckler.org\/blog\/wp-content\/uploads\/2016\/02\/box_assembled_top.jpg\")
<\/p>\n![\"box_assembled_bottom\"](\"https:\/\/www.mbeckler.org\/blog\/wp-content\/uploads\/2016\/02\/box_assembled_bottom.jpg\")
<\/p>\n![\"box_misalign_2\"](\"https:\/\/www.mbeckler.org\/blog\/wp-content\/uploads\/2016\/02\/box_misalign_2.jpg\")
<\/p>\n![\"box_misalign_1\"](\"https:\/\/www.mbeckler.org\/blog\/wp-content\/uploads\/2016\/02\/box_misalign_1.jpg\")
<\/p>\n![\"box_test_fit\"](\"https:\/\/www.mbeckler.org\/blog\/wp-content\/uploads\/2016\/02\/box_test_fit.jpg\")
<\/p>\nProduction Step 2 – Add edging and hardware<\/h1>\n
![\"edging_and_hardware\"](\"https:\/\/www.mbeckler.org\/blog\/wp-content\/uploads\/2016\/02\/edging_and_hardware.jpg\")
<\/p>\n![\"hinges\"](\"https:\/\/www.mbeckler.org\/blog\/wp-content\/uploads\/2016\/02\/hinges.jpg\")
<\/p>\n![\"handle_detail\"](\"https:\/\/www.mbeckler.org\/blog\/wp-content\/uploads\/2016\/02\/handle_detail.jpg\")
<\/p>\nProduction Step 3 – Artwork<\/h1>\n
![\"one_art_please\"](\"https:\/\/www.mbeckler.org\/blog\/wp-content\/uploads\/2016\/02\/one_art_please-300x221.jpg\")
<\/p>\n![\"art_oak_lasering\"](\"https:\/\/www.mbeckler.org\/blog\/wp-content\/uploads\/2016\/02\/art_oak_lasering.jpg\")
<\/p>\n![\"crest_deepness\"](\"https:\/\/www.mbeckler.org\/blog\/wp-content\/uploads\/2016\/02\/crest_deepness.jpg\")
<\/p>\n